Seat leakage classification through control valves.
Control valves are designed to throttle flows and they are not necessary able to close 100% with no leakage.
The shut off ability has to do with type of valve. Double seated control valves have very poor shut off capabilities. In addition - the guiding, the seat material, the actuator thrust, the pressure drop and the type of fluid all play part in how well particular control valves shuts off.
Seat Leakage Classifications
There are actually six different seat leakage classifications defined by ANSI/FCI 70-2 2006 (European equivalent standard IEC 60534-4).
The most commonly used are
- CLASS IV
- CLASS Vl
CLASS IV is also known as metal to metal. It is the kind of leakage rate you can expect from a valve with a metal plug and a metal seat.
CLASS Vl is known as soft seat classification. Soft Seat Valves are those where either the plug or seat or both are made from some kind of composition material such asPolytetrafluoroethylene (PTFE) or similar.
Valve Leakage Classifications
Class I - Valve Leakage Classifications
Identical to Class II, III, and IV in construction and design intent, but no actual shop test is made. Cass I is also known as dust tight and can refer to metal or resilient seated valves.
Class II - Valve Leakage Classifications
Intended for double port or balanced singe port valves with a metal piston ring seal and metal to metal seats.
- 0.5% leakage of full open valve capacity
- Service dP or 50 psid (3.4 bar differential), whichever is lower at 50 to 125 oF
- Test medium air at 45 to 60 psig is the test fluid
Typical constructions:
- Balanced, single port, single graphite piston ring, metal seat, low seat load
- Balanced, double port, metal seats, high seat load
Class III - Valve Leakage Classifications
Intended for the same types of valves as in Class II.
- 0.1% leakage of full open valve capacity
- Service dP or 50 psid (3.4 bar differential), whichever is lower at 50 to 125 oF
- Test medium air at 45 to 60 psig is the test fluid
Typical constructions:
- Balanced, double port, soft seats, low seat load
- Balanced, single port, single graphite piston ring, lapped metal seats, medium seat load
Class IV - Valve Leakage Classifications
Intended for single port and balanced single port valves with extra tight piston seals and metal to-metal seats.
- 0.01% leakage of full open valve capacity
- Service dP or 50 psid (3.4 bar differential), whichever is lower at 50 to 125 oF
- Test medium air at 45 to 60 psig is the test fluid
Typical constructions:
- Balanced, single port,Polytetrafluoroethylene (PTFE) piston ring, lapped metal seats, medium seat load
- Balanced, single port, multiple graphite piston rings, lapped metal seats
- Unbalanced, single port, lapped metal seats, medium seat load
- Class IV is also known as metal to metal
Class V - Valve Leakage Classifications
Intended for the same types of valves as Class IV
- The test fluid is water at 100 psig or operating pressure
- Leakage allowed is limited to 5 x 10-4 ml per minute per inch of orifice diameter per psi differential
- Service dP at 50 to 125 oF
Typical constructions:
- Unbalanced, single port, lapped metal seats, high seat load
- Balanced, single port,Polytetrafluoroethylene (PTFE) piston rings, soft seats, low seat load
- Unbalanced, single port, soft metal seats, high seat load
Class Vl - Valve Leakage Classifications
Class Vl is known as a soft seat classification. Soft Seat Valves are those where the seat or shut-off disc or both
are made from some kind of resilient material such as Polytetrafluoroethylene (PTFE). Intended for resilient seating valves.
- The test fluid is air or nitrogen
- Pressure is the lesser of 50 psig or operating pressure
- The leakage limit depends on valve size and ranges from 0.15 to 6.75 ml per minute for valve sizes 1 through 8 inches
| Port Diameter | Bubbles per minute | ml per minute | |
|---|---|---|---|
| inches | mm | ||
| 1 | 25 | 1 | 0.15 |
| 1 1/2 | 38 | 2 | 0.30 |
| 2 | 51 | 3 | 0.45 |
| 2 1/2 | 64 | 4 | 0.60 |
| 3 | 76 | 6 | 0.90 |
| 4 | 102 | 11 | 1.70 |
| 6 | 152 | 27 | 4.00 |
| 8 | 203 | 45 | 6.75 |
| 10 | 254 | 63 | 9 |
| 12 | 305 | 81 | 11.5 |
Typical constructions:
- Unbalanced, single port, soft seats, low load
Control Valve Leakage Classification - Overview
| Leakage Class Designation | Maximum Leakage Allowable | Test Medium | Test Pressure | Testing Procedures Required for Establishing Rating |
|---|---|---|---|---|
| I | x | x | x | No test required |
| II | 0.5% of rated capacity | Air or water at 50 - 125o F (10 - 52oC) | 45 - 60 psig or maximum operating differential whichever is lower | 45 - 60 psig or maximum operating differential whichever is lower |
| III | 0.1% of rated capacity | As above | As above | As above |
| IV | 0.01% of rated capacity | As above | As above | As above |
| V | 0.0005 ml per minute of water per inch of port diameter per psi differential | Water at 50 to125oF (10 to 52oC) | Maximum service pressure drop across valve plug not to exceed ANSI body rating | Maximum service pressure drop across valve plug not to exceed ANSI body rating |
| VI | Not to exceed amounts shown in the table above | Air or nitrogen at 50 to 125o F (10 to 52oC) | 50 psig or max rated differential pressure across valve plug whichever is lower | Actuator should be adjusted to operating conditions specified with full normal closing thrust applied to valve plug seat |
Related Topics
Control Valve Sizing
Control Valve terminology, bodies, trim, flow characteristics, Cv and Kv sizing, noise, actuators, positioners and more.
Related Documents
API 6D Valves - Pressure Ratings vs. Temperature
Temperature and pressure ratings for valves according API 6D.ASTM A216 Valves - Pressure Ratings vs. Temperature
Pressure and temperature ratings for cast carbon steel valves.Control Valves - Flow Characteristics
Flow capacities vs. stem opening.NDT - Non Destructive Testing
Non-destructive construction testing.Steam Control Valves - Calculate Flow Factor Kv
Designing steam control valves and their Kv values.Valve Selection Guide
Applications guide for selecting valves.Valve Type Classifications
Categories of valves.Valves - Specific Services
In case of a specific service - the choose of a valve may be simplified by following an established practice.Valves - Typical Operating Temperatures
Operating temperatures for typical categories of valves - ball valves, butterfly valves and more.Valves Types - Operating Size Ranges
Types of valves and their typical operating sizes.Water Control Valves - Kv Calculation
Designing water process control valves and their Kv values.
Search
Search is the most efficient way to navigate the Engineering ToolBox.
- Popular internal searches in the Engineering ToolBox
Engineering ToolBox - SketchUp Extension - Online 3D modeling!
Add standard and customized parametric components - like flange beams, lumbers, piping, stairs and more - to your Sketchup model with the Engineering ToolBox - SketchUp Extension - enabled for use with older versions of the amazing SketchUp Make and the newer "up to date" SketchUp Pro. Add the Engineering ToolBox extension to your SketchUp Make/Pro from the Extension Warehouse!
Translate this Page
Translate this page to Your Own Language.
About the Engineering ToolBox!
Privacy Policy
We don't collect information from our users. More about
- the Engineering ToolBox Privacy Policy
We use a third-party to provide monetization technologies for our site. You can review their privacy and cookie policy here.
You can change your privacy settings by clicking the following button: .
Advertise in the ToolBox
If you want to promote your products or services in the Engineering ToolBox - please use Google Adwords. You can target the Engineering ToolBox by using AdWords Managed Placements.
Citation
This page can be cited as
- The Engineering ToolBox (2003). Control Valves - Leakage Classification. [online] Available at: https://www.engineeringtoolbox.com/control-valves-leakage-d_484.html [Accessed Day Month Year].
Modify the access date according your visit.
